Play-Doh Toy Time Race Game
Play-Doh Toy Time Race Game Rulebook
Table of Contents
Table of Contents
Contents
Gameboard, 4 Two-Ounce Cans of PLAY-DOH Compound, 4 Plastic Gears, Hubs and Bases, Recycle Stamper, 4 Toy Molds (Mr. Potato Head, Chuck the Dump Truck, My Little Pony and Can of PLAY-DOH), Spinner board, base and arrow, Gift Box, Recycle Box.
Adult Assembly Required.
Object
Race your PLAY-DOH toys through the Fun Factory toward the Gift Box at the end of the Fun Factory Assembly Line. Have fun moving along the gears and turning them round and round... but watch out for the Recycle Stamper! To win, be the first to get two toys into the Gift Box!
Game Setup
This illustration shows a 4-player game ready to play. Please refer to it as you assemble and set up your game.
(The printed setup diagram labels the gift box, recycle box, recycle stamper, finish line, toy molds, toys on start, and spinner. The sheet gives no further written setup text beyond the steps under Getting Ready to Play.)
Assembling Your Game Parts
Remove the game parts from their cardboard sheets and plastic wrappings. Discard the waste. Carefully detach the spinner base, arrow, and toy molds from their plastic runners. Discard the runners. If needed, use an emery board or sandpaper to remove any excess plastic from the game parts.
Spinner Assembly
(Assembly is illustrated only; the sheet gives no written steps for the spinner.)
Toy Mold Assembly
Be sure to match up the correct halves of each toy mold!
Gift & Recycle Box Assembly
Assemble the gift box as shown here. Then assemble the recycle box the same way.
Note: The recycle box has no lid.
- Fold along all dotted lines.
- Fold in the side tabs, then fold up the bottom and lock in.
Getting Ready to Play
Attach the Gears to the Board
Attach each of the four gears to the gameboard as shown here. Then line them up with their outlines on the board.
- Center a base under a gameboard hole with the peg facing up.
- Press a gear design-side up onto the base peg, then snap it in. Make sure the base peg is centered.
- Then press and snap a hub onto the gear.
Make Your Toys!
Choose a toy mold and any color of PLAY-DOH compound. Then make each toy as shown here. Place any extra compound back in the can and close the lid securely. Start the game with two toys on the gameboard.
- Place a small wad of PLAY-DOH compound in the open mold.
- Press the mold together firmly.
- Tap out your toy. Remove any excess compound and replace in the can.
Extra toys: You can have any number of toys on the board at one time, so make as many as you want! You'll also need extras to replace any toys that get recycled.
How To Play
The youngest player goes first. Play then continues to the left.
On Your Turn: Spin the spinner, then follow the rules below. Your turn is then over.
- 1 2 3 4 (spinner result): Move any one of your toys the number of spaces you spun.
- Recycle icon (spinner result): Recycle another player's toy!
- Gear icon (spinner result): Turn the gears and watch the toys move!
Gameboard Spaces
Move your toy from space to connecting space along the Fun Factory Assembly Line, toward the PLAY-DOH Can at the end. If you end your move on a space with another toy, just jump ahead to the next open space. All of the spaces your toys may land on are described below.
- Start Space: All toys start the game on this space.
- Red and Green Spaces: If your toy lands on any of these spaces, your turn is over.
- The Shortcut Arrow: If your toy is lucky enough to land here, slide it to the gear space at the end of the tube!
- Gear Spaces: Each gear has five gear spaces. You may move onto a gear space from any connecting space, and off of a gear space to any connecting space. See MOVING ON THE GEARS for the right and wrong way to move along gear spaces.
- Hub Spaces: If your toy lands on the space in the center of a gear, it is safe from being squished by the Recycle Stamper!
- Finish Space: You must move your toy onto the PLAY-DOH Can Finish space at the end of the Fun Factory Assembly Line to put your toy in the Gift Box. You don't need to spin the exact number to reach the Finish space.
Moving on the Gears
Moving your toys along the gears is easy! Be sure to move to connecting spaces only.
The blue toy can move to any of the spaces right next to it. But it can't move to any of the spaces, because they're too far away!
Recycling Toys
Choose any opponent's toy that's not on a Safe space. Then take the Recycle Stamper and press down to squish that toy flat! Place the recycled toy into the Recycle Box on the board. If you run low on PLAY-DOH compound, you may reuse some from the toys in the Recycle Box.
Turning Gears
Turn the hub of any gear in any direction as much as you want. This will move all of the gears on the gameboard, and any toys on the gear spaces will move with the gears!
Make sure to line the gears up with the outline on the board after turning them.
It's good strategy to turn the gears so that your toys move forward and opponents' toys move back. This player moved her Mr. Potato Head forward, and an opponent's Chuck the Dump Truck back.
Winning the Game
If you're the first player to get two toys to the PLAY-DOH Can Finish space at the end of the Fun Factory Assembly Line, you win the game! Continue the fun and pack up your two winning toys in the Gift Box!
Game for Younger Players
Instead of getting two toys to the Finish space, younger players can win after getting only one toy to the Finish space first.
Out of PLAY-DOH Compound?
Look for PLAY-DOH compound wherever toys and games are sold.
Storing Your Game
Remove the toys and boxes from the play area, store PLAY-DOH compound back in the cans, and close the lids securely. To store your game in the box, remove each gear from the gameboard by carefully and firmly lifting them up to detach them from their bases. You can leave the hubs on the gears for storage, but the next time you play you may need to remove them to reattach the gears to the gameboard.